 |
|||
|
|
|||
|
Page Title:
WINDSHIELD WIPER SWITCH, MOTOR, AND CONLINK COVERS REPLACEMENT - continued |
|
||
| ||||||||||
|
|
 TM 9-2320-386-24-1-1
0232 00
WINDSHIELD WIPER SWITCH, MOTOR, AND CONLINK COVERS REPLACEMENT (Contd)
REMOVAL
1.
Remove four screws (3), lockwashers (4), washers (2), two screws (7), and lockwashers (8) from
left conlink cover (1), right conlink cover (9), and windshield frame (11). Discard lockwashers (4)
and (8).
2.
Disconnect harness leads 27 and 71 (19) from wiper switch (18).
3.
Remove screw (21), lockwasher (22), ground (GND) wire 57 (20), and lockwasher (23) from wiper
motor (27). Discard lockwashers (22) and (23).
4.
Remove screw (16) and lockwasher (15) from mounting bracket (10) and windshield frame (11).
Discard lockwasher (15).
5.
Remove left (1) and right (9) conlink covers, wiper motor (27), wiper switch (18), and mounting
bracket (10) from windshield frame (11) as an assembly.
6.
Remove three locknuts (12), screws (5), lockwashers (6), left conlink cover (1), and right conlink
cover (9) from wiper motor (27) and mounting bracket (10). Discard locknuts (12) and lockwashers (6).
7.
Remove locknut (14), retainer bracket (13), and wiper motor (27) from mounting bracket (10).
Discard locknut (14).
8.
Disconnect wiper switch lead (17) from wiper motor (27).
9.
Depress retaining clip on knob (26) and remove knob (26), nut (25), lockwasher (24), and wiper
switch (18) from wiper motor (27). Discard lockwasher (24).
INSTALLATION
1.
Install wiper switch (18) on wiper motor (27) with new lockwasher (24) and nut (25). Tighten
nut (25) 35 lb-in. (4 Nm).
2.
Depress retaining clip on knob (26) and install knob (26) on wiper switch (18).
3.
Connect wiper switch lead (17) to wiper motor (27).
4.
Install wiper motor (27) and retainer bracket (13) on mounting bracket (10) with new locknut (14).
5.
Install left conlink cover (1) and right conlink cover (9) on wiper motor (27) and mounting
bracket (10) with three new lockwashers (6), screws (5), and new locknuts (12).
6.
Position left conlink cover (1) and right conlink cover (9), wiper motor (27), wiper switch (18), and
mounting bracket (10) on windshield frame (11) as an assembly.
7.
Install four washers (2), new lockwashers (4), screws (3), two new lockwashers (8), and screws (7)
on left conlink cover (1), right conlink cover (9), and windshield frame (11).
8.
Install mounting bracket (10) and wiper motor (27) on windshield frame (11) with new
lockwasher (15) and screw (16).
9.
Install new lockwasher (23), ground (GND) wire 57 (20), new lockwasher (22), and screw (21) on wiper
motor (27).
10.
Connect harness leads 27 and 71 (19) to wiper switch (18).
11.
Connect battery ground cable (WP 0121 00).
0232 00-2
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for a printable version