Special Information. - TM-9-2320-209-34P0015

TM 9-2320-209-34P

Unit of Measure (U/M). Indicates the standard

R e p a r a b l e item. When uneconomically

of the basic quantity of the listed item as used in

reparable, condemn and dispose at the direct

performing the actual maintenance function. This meausre

support level.

is expressed by a two-character alphabetical abbreviation

R e p a r a b l e item. When uneconomically

(e.g., ea, in, pr, etc.). When the unit of measure differs from

the unit of issue, the lowest unit of issue that will satisfy

reparable, condemn and dispose at the general

the required units of measure will be requisitioned.

support level.

Quantity Incorporated in Unit. Indicates the

Reparable item, When beyond lower level repair

quantity of the item used in the breakout shown on the

capability, return to depot. Condemnation and

illustration figure, which is prepared for a functional group

disposal not authorized below depot level.

or an assembly. A "V" appearing in this column in lieu of a

quantity indicates that no specific quantity is applicable,

Reparable item. Repair, condemnation, and

(e.g., shims, spacers, etc.).

disposal not authorized below depot/specialized

repair activity level.

4. Special Information.

Item requires special handling or condemnation

Usable on codes are shown in the description

procedures because of specific reasons (i.e.,

column. Uncoded items are applicable to all models, unless

precious metal content, high dollar value,

o t h e r w i s e indicated by model application in the

critical material or hazardous material). Refer

description column, Identification of the usable on codes

to appropriate manuals/directives for specific

used in this publication are:

instructions.

Code

Used On

National Stock Number. Indicates the National

stock number assigned to the item and will be used for

All models equipped with gasoline engine

requisitioning purposes.

Model OA-331

Part Number. Indicates the primary number

All models equipped with the multi-fuel LDS-

used by the manufacturer (individual, company, firm,

427-2 engine

corporation, or Government activity), which controls the

design and characteristics of the item by means of its

All models equipped with multi-fuel engines

engineering drawings, specifications standards, and

LD-465-1, LD-465-1C or LDT-465-1 C

inspection requirements, to identify an item or range of

items.

All models equipped with front winch

NOTE: When a stock numbered item is requisitioned, the

All models equipped with power takeoff

repair part received may have a different part number than

References to the M44A2 series apply only to

the part number than the part being replaced.

the multifuel clean air engine (LDT 465-1 C, NSN 2815-00-

103-2642). Some figures include the words "clean air" in

Federal Supply Code for Manufacturer (FSCM).

parentheses to designate this.

The FSCM is a 5 digit numeric code listed in SB 708-42

which is used to identify the manufacturer, distributor, or

Detailed manufacturing instructions for items

Government agency, etc.

source coded to be manufactured or fabricated are found

in TM 9-2320-209-20/1 (TM 9-2320-209-20, gasoline

Description. Indicates the Federal item name

models only) and TM 9-2320-209-34 (TM 9-2320-209-35,

and, if required, a minimum description to identify the

gasoline models only). Bulk materials required to

item. Items that are included in kits and sets are listed

manufacture items are listed in the Bulk Material Group

below the name of the kit or set with the quantity of each

9501 of this manual.

item in the kit or set indicated in the quantity incorporated

in unit column. When the part to be used differs between

Detailed assembly instructions for items

serial numbers of the same model, the effective serial

source coded to be assembled are found in TM 9-2320-209-

numbers are shown as the last line of the description. In the

20/1 (TM 9-2320-209-20, gasoline models only) and TM 9-

Special Tools List, the initial basis of issue (BOI) appears as

2320-209-34 (TM 9-2320-209-35, gasoline models only).

the last line in the entry for each special tool, TMDE, and

Assembly components are listed immediately following

support equipment. When density of equipments supported

the item to be assembled.

exceeds density spread indicated in the basis of issue, the

total authorization is increased accordingly.

Repair parts kits and gasket sets appear as the

last entries in the repair parts listing for the figure in which

its parts are listed as repair parts.

1 vii

Change