Quantcast TRANSMISSION (IN-VEHICLE) REPLACEMENT - continued - TM-9-2320-386-24-1-20357

 

Click here to make tpub.com your Home Page

Page Title: TRANSMISSION (IN-VEHICLE) REPLACEMENT - continued
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
TRANSMISSION (IN-VEHICLE) REPLACEMENT - continued - TM-9-2320-386-24-1-20356
Up
/.5ton/TM-9-2320-386-24-1-2 Extended Service Program (ESP) for 2-1/2-Ton 6x6 M44A3 Series Trucks (Diesel) Manual
Next
TRANSMISSION (IN-VEHICLE) REPLACEMENT - continued - TM-9-2320-386-24-1-20358
TM 9-2320-386-24-1-2
0335 00
TRANSMISSION (IN-VEHICLE) REPLACEMENT (Contd)
20.
Remove screw (2), lockwasher (1), ground strap (8), and lockwasher (9) from transmission (3) and
adapter (4). Discard lockwashers (1) and (9).
WARNING
Keep rear of transmission tilted slightly downward until two
retaining brackets can be installed to prevent converter from
separating from transmission and causing injury to personnel or
damage to equipment.
NOTE
Transmission has two screws installed where transmission lifting
fixture is installed. Remove screws from transmission and use
with fixture.
21.
Remove screw (5), clamp (6), and oil inlet hose (7) from adapter (4).
22.
Disconnect plug with leads 380 and 380A (16) from backup light switch (15).
23.
Install transmission lifting fixture on transmission (3) with two screws (11) and screw (10), and
connect sling in number two front hole and rear hole of transmission lifting fixture. Install sling to
lifting device.
WARNING
Install transmission jack under transmission when performing
steps 24 through 27 to support transmission and prevent injury to
personnel.
24.
Remove ten screws (2), lockwashers (1), and transmission (3) from adapter (4). Ensure rear of
transmission (3) is tilted slightly downward as transmission (3) is removed from adapter (4).
Discard lockwashers (1).
NOTE
If replacing AT1545P transmission with AT545 transmission, the
flywheel and related parts must be replaced. Refer to WP 0337 01.
25.
Remove six screws (12) and ring (14) from torque converter (13). If replacing AT1545P transmission
with AT545 transmission, discard screws (12) and ring (14).
NOTE
Check that converter has not moved forward before and after
installing retaining brackets. Measure distance from flat on
converter to lip on transmission housing. Distance cannot be more
than 1.5 in. (38 mm).
26.
Install two retaining brackets (19), one at 4 o'clock position and one at 8 o'clock position, on
transmission (3) and converter (13) with four washers (18) and (20) and screws (17) and (21).
27.
Remove twelve screws (23) and adapter (4) from flywheel housing (22). If replacing AT1545P
transmission with AT545 transmission, discard adapter (4).
2
TRANSMISSION
SLING
LIFTING
1
10
FIXTURE
3
11
6
4
5
4
3
9
7
2
1
8
Change 1
0335 00-6

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business