Quantcast STE/ICE-R WIRING HARNESS REPLACEMENT - continued - TM-9-2320-386-24-1-20325

 

Click here to make tpub.com your Home Page

Page Title: STE/ICE-R WIRING HARNESS REPLACEMENT - continued
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
STE/ICE-R WIRING HARNESS REPLACEMENT - continued - TM-9-2320-386-24-1-20324
Up
/.5ton/TM-9-2320-386-24-1-2 Extended Service Program (ESP) for 2-1/2-Ton 6x6 M44A3 Series Trucks (Diesel) Manual
Next
STE/ICE-R WIRING HARNESS REPLACEMENT - continued - TM-9-2320-386-24-1-20326
TM 9-2320-386-24-1-2
0331 00
STE/ICE-R WIRING HARNESS REPLACEMENT (Contd)
25.
Remove ten screws (22) and glovebox (21) from instrument panel (5).
26.
Disconnect tachometer plug (2) from STE/ICE-R connector leads 770-C and 770-D (3).
27.
Remove cap (18) from STE/ICE-R receptacle (12).
28.
Remove four locknuts (11), screws (20), cap chain (19), and STE/ICE-R receptacle (12) from
instrument panel (5). Discard locknuts (11).
29.
Remove nut (8), lockwasher (9), screw (16), lockwasher (15), ground (GND) lead (14) of panel
harness (7), and STE/ICE-R harness ground (GND) lead (13) from glovebox support bracket (10).
Discard lockwashers (9) and (15).
CAUTION
Use care when removing STE/ICE-R wiring harness. Pulling a snagged or
attached harness from the vehicle may result in damage to equipment.
30.
Remove grommet (1) from STE/ICE-R wiring harness (6) and firewall (4).
31.
Route STE/ICE-R wiring harness (6) out from behind instrument panel (5) and remove STE/ICE-R
wiring harness (6) from vehicle.
INSTALLATION
NOTE
If new STE/ICE-R wiring harness is to be installed, transfer tags
installed at removal on old harness to new harness.
If STE/ICE-R wiring harness requires repair, refer to WP 0125 00
for further instructions.
1.
Route STE/ICE-R wiring harness (6) into vehicle and behind instrument panel (5) with panel
harness (7).
NOTE
STE/ICE-R wiring harness is engineered for each vehicle
configuration. Adjust STE/ICE-R wiring harness to remove slack
or allow slack as required for proper installation.
2.
Install STE/ICE-R harness ground (GND) lead (13) and panel harness ground (GND) lead (14) on
glovebox support bracket (10) with new lockwashers (15) and (9), screw (16), and nut (8).
NOTE
Install STE/ICE-R receptacle on instrument panel with key
positioned at top.
3.
Position STE/ICE-R receptacle (12) through hole (17) in instrument panel (5), align mounting holes,
and install cap chain (19) and STE/ICE-R receptacle (12) on instrument panel (5) with four
screws (20) and new locknuts (11).
4.
Install cap (18) on STE/ICE-R receptacle (12).
5.
Connect tachometer plug (2) to STE/ICE-R leads 770-C and 770-D on connector (3).
6.
Install grommet (1) on STE/ICE-R wiring harness (6) and route STE/ICE-R wiring harness (6)
through firewall (4).
7.
Install glovebox (21) on instrument panel (5) with ten screws (22).
0331 00-8

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business