Quantcast FUEL TRANSFER PUMP REPAIR - continued - TM-9-2320-386-24-1-20261

 

Click here to make tpub.com your Home Page

Page Title: FUEL TRANSFER PUMP REPAIR - continued
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
FUEL TRANSFER PUMP REPAIR - continued - TM-9-2320-386-24-1-20260
Up
/.5ton/TM-9-2320-386-24-1-2 Extended Service Program (ESP) for 2-1/2-Ton 6x6 M44A3 Series Trucks (Diesel) Manual
Next
FUEL TRANSFER PUMP REPAIR - continued - TM-9-2320-386-24-1-20262
TM 9-2320-386-24-1-2
0324 00
FUEL TRANSFER PUMP REPAIR (Contd)
15.
Remove three screws (2), transfer pump cover (1), spring (9), and spacer sleeve (8) from governor (3).
Discard spring (9) and spacer sleeve (8).
NOTE
Mark position of sleeve orifice on governor for installation.
16.
Remove O-ring (5), piston assembly (7), and O-ring (5) from governor (3). Discard O-rings (5) and
piston assembly (7).
CLEANING AND INSPECTION
1.
For general cleaning instructions, refer to WP 0383 00.
2.
For general inspection instructions, refer to WP 0383 00.
3.
Inspect cam surface of tappet (6) for wear. Replace governor (3) if tappet (6) is worn.
ASSEMBLY
1.
Apply lubricating oil to inlet bore (21), outlet bore (20), and piston bore (4) of governor (3),
adapter (17), inlet fitting (26), spacer sleeve (8), and check valves (19) and (28).
2.
Install new O-ring (5), new piston assembly (7), and new O-ring (5) in piston bore (4) of
governor (3).
3.
Install new spacer sleeve (8), new spring (9), and transfer pump cover (1) on governor (3) with three
screws (2).
4.
Install new O-ring (27) on inlet fitting (26).
5.
Install new check valve (28) and inlet fitting (26) on inlet bore (21) of governor (3).
6.
Install new O-ring (18) on adapter (17).
7.
Install new check valve (19) and adapter (17) on outlet bore (20) of governor (3).
8.
Install new O-ring (16) and fuel line (15) on adapter (17).
9.
Install new O-ring (25) on adapter (24).
10.
Install adapter (24), elbow (23), and fuel inlet hose (22) on inlet fitting (26).
11.
Install washer (31) and screw (32) on fuel return hose assembly (30).
12.
Install manual control lever (33) on throttle lever (29) with washer (14) and screw (13).
13.
Install two springs (12) and manual control lever (34) on throttle lever (29) and manual control
lever (33) with washer (11) and screw (10).
14.
Install double-angle throttle bracket (45) and ball joint (40) on manual control lever (34) with
washer (44) and nut (43).
15.
Pull sleeve (41) back on accelerator cable (42) and install on ball joint (40).
16.
Insert throttle cable (38) through pivot (39), install stop collar (37), and tighten screw (36).
17.
Install spring (35) on bracket (46) and double-angle throttle bracket (45).
0324 00-4

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business