Quantcast FUEL SETTING ADJUSTMENT - continued - TM-9-2320-386-24-1-20251

 

Click here to make tpub.com your Home Page

Page Title: FUEL SETTING ADJUSTMENT - continued
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
FUEL SETTING ADJUSTMENT - continued - TM-9-2320-386-24-1-20250
Up
/.5ton/TM-9-2320-386-24-1-2 Extended Service Program (ESP) for 2-1/2-Ton 6x6 M44A3 Series Trucks (Diesel) Manual
Next
FUEL SETTING ADJUSTMENT - continued - TM-9-2320-386-24-1-20252
TM 9-2320-386-24-1-2
0323 00
FUEL SETTING ADJUSTMENT (Contd)
NOTE
Ensure clamping screw is not protruding from threaded hole on hook
end of control linkage positioning tool. Any protrusion will result in
improper installation of control linkage positioning tool.
6.
Turn clamping screw on control linkage positioning tool until end of clamping screw is inside of
threaded hole.
7.
Turn limit screw on control linkage positioning tool until nylon spacer is seated against control
linkage positioning tool.
8.
Position control linkage positioning tool on control linkage shaft (2) between No. 4 (1) and No. 5 (3)
rocker arm supports.
CAUTION
Once installed, the control linkage positioning tool must not be
removed, loosened, or allowed to slip on the control linkage shaft. If the
control linkage positioning tool does not stay clamped in this position
until after double zero is set, the control linkage positioning tool must
be tightened again before double zero can be set.
NOTE
Ensure limit screw seats against cylinder head while tightening
clamping screw.
9.
Install control linkage positioning tool on control linkage shaft (2) by pressing down on limit screw
while tightening clamping screw until it grips control linkage shaft (2) securely.
NOTE
Rotating the control linkage shaft toward the push rod side of engine
will move all rack bars toward the "fuel-off" position and help free any
rack bars which may be hanging up or binding.
Ensure control linkage positioning tool moves freely and does not touch
rocker arm supports.
Ensure limit screw seats against cylinder head when control linkage
positioning tool is released.
10.
Move control linkage positioning tool toward push rod side of engine to rotate control linkage
shaft (2), then release.
NOTE
When the fuel shutoff solenoid is removed, the rack bars move into the
"fuel-on" position. This is necessary to set and check the fuel setting.
11.
Remove fuel shutoff solenoid (WP 0050 00).
12.
Move control linkage positioning tool toward push rod side of engine and hold.
NOTE
Assistant will help with step 13.
13.
Set double zero on the horizontal dial indicator.
a. Loosen red thumb screw on side of holding fixture and slide horizontal dial indicator laterally
until small needle lines up on zero. Tighten red thumb screw.
b. Loosen bezel screw on horizontal dial indicator and turn bezel until large needle lines up on
zero. Tighten bezel screw.
14.
Release control linkage positioning tool.
15.
Pull and release control linkage positioning tool several times to ensure horizontal dial indicator
reads double zero on the push rod side of engine.
a. If horizontal dial indicator does read double zero, go to step 16.
b. If horizontal dial indicator does not read double zero, repeat steps 12 through 15.
0323 00-4

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business