Quantcast FUEL INJECTION CONTROL LINKAGE MAINTENANCE - continued - TM-9-2320-386-24-1-20227

 

Click here to make tpub.com your Home Page

Page Title: FUEL INJECTION CONTROL LINKAGE MAINTENANCE - continued
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
FUEL INJECTION CONTROL LINKAGE MAINTENANCE - continued - TM-9-2320-386-24-1-20226
Up
/.5ton/TM-9-2320-386-24-1-2 Extended Service Program (ESP) for 2-1/2-Ton 6x6 M44A3 Series Trucks (Diesel) Manual
Next
FUEL INJECTION CONTROL LINKAGE MAINTENANCE - continued - TM-9-2320-386-24-1-20228
TM 9-2320-386-24-1-2
0320 00
FUEL INJECTION CONTROL LINKAGE MAINTENANCE (Contd)
CLEANING AND INSPECTION
WARNING
Skysol-100 mixture is combustible. Use mechanical ventilation whenever
product is used in a confined space, is heated above ambient
temperatures, or is agitated. DO NOT use or store near heat, sparks,
flame, or other ignition sources. Keep container sealed when not in use.
Contact with Skysol-100 may cause skin irritation. Use chemical resistant
gloves. In case of skin contact, remove any contaminated clothing and
wash skin thoroughly with soap and water. Wash contaminated clothing
before reuse. Eye contact may cause irritation, tearing, or blurring of
vision. Use face shield or goggles when eye contact may occur. In case of
eye contact, flush eyes with large amounts of water for at least fifteen
(15) minutes or until irritation subsides. Inhalation may cause irritation
to upper respiratory passages. DO NOT have food or drink in the vicinity.
1.
Clean fuel injection control linkage (2) with Skysol-100 and dry with lint-free cloth.
2.
Inspect fuel injection control linkage (2) for bends, breaks, cracks, binding, and wear. Replace fuel
injector control linkage (2) if damaged.
INSTALLATION
CAUTION
Fuel injector springs must be compressed to allow free movement
of the injector rack. Failure to do so may result in damage to fuel
injectors.
1.
Position fuel injection control linkage (2) on cylinder head (3).
2.
Slide link (4) on fuel injection control linkage (2) through sleeve (5).
3.
Engage six fuel injector control arms (6) with fuel injector control racks (7).
CAUTION
Fuel injector control arms on the fuel injection control linkage must
be aligned with each fuel injector control rack before tightening
screws. Failure to comply may result in damage to equipment.
NOTE
Ensure small dowel in each mounting bracket is properly aligned
before tightening screws.
4.
Install fuel injection control linkage (2) on cylinder head (3) with four screws (1).
5.
Install new O-ring (11) on sleeve (5).
6.
Install clevis (8) on link (4) with pin (12) and new retaining ring (9).
7.
Using soft-jawed pliers, slide sleeve (5) from cylinder head (3) into governor (13).
8.
Install clip (10) on sleeve (5).
9.
Install rocker arm assemblies and pushrods (WP 0309 00).
10.
Perform fuel injector syncronization (WP 0321 00).
0320 00-4

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business