Quantcast ENGINE OIL PUMP MAINTENANCE - continued - TM-9-2320-386-24-1-20193

 

Click here to make tpub.com your Home Page

Page Title: ENGINE OIL PUMP MAINTENANCE - continued
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
ENGINE OIL PUMP MAINTENANCE - continued - TM-9-2320-386-24-1-20192
Up
/.5ton/TM-9-2320-386-24-1-2 Extended Service Program (ESP) for 2-1/2-Ton 6x6 M44A3 Series Trucks (Diesel) Manual
Next
ENGINE OIL PUMP MAINTENANCE - continued - TM-9-2320-386-24-1-20194
TM 9-2320-386-24-1-2
0313 00
ENGINE OIL PUMP MAINTENANCE (Contd)
INSPECTION
WARNING
Volatile mineral spirits burn easily and fumes can explode. Do not
smoke or allow open flame nearby when using mineral spirits.
Failure to do so may cause serious injury or death to personnel.
1.
All metallic parts should be cleaned thoroughly with mineral spirits and dried with lint-free cloth.
2.
Inspect metallic parts including impellers (4) and (13) for chips, cracks, or burrs. Replace any part
with visible chips or cracks.
3.
Inspect oil pump body (3) and oil pump body assembly (5) for cracks, casting imperfections,
damaged threads, and scoring. If damaged, replace oil pump body (3) or body assembly (5).
4.
Inspect pressure relief plunger (9) for scoring, burrs, and sticking. If pressure relief plunger (9) is
scored or sticking, replace pressure relief plunger (9).
5.
Insert impellers (4) and (13) into oil pump body assembly (5) and oil pump body (3). If loose in oil pump
body (3) or oil pump body assembly (5), replace oil pump body assembly (5) and oil pump body (3).
6.
Inspect intake tube (15) for broken wire mesh in screen (18). If screen (18) is broken or has been
removed from intake tube (15), replace intake tube (15).
ASSEMBLY
1.
Install pressure relief plunger (9), spring (10), and retaining washer (12) on oil pump body
assembly (5) with screw (11).
2.
Position impeller (4) on oil pump body assembly (5), and using arbor press, install driven gear (8)
onto impeller (4) until flush with shaft of impeller (4).
3.
Install impeller (13) on oil pump body (3).
4.
Install oil pump body (3) on oil pump body assembly (5) with four washers (6) and screws (7).
5.
Install new gasket (14) and intake tube (15) on oil pump body (3) with two washers (16) and screws (17).
6.
Install new O-ring (2) and outlet elbow (1) on oil pump body (3) with screw (19).
7.
Apply sealing compound to screw (29), and install spacer (25), bearing (26), idler gear (27), and
washer (28) on oil pump body assembly (5) with screw (29). Tighten screw (29) 39-61 lb-ft (53-83 Nm).
INSTALLATION
1.
Install new O-ring (21) and oil pump body assembly (5) on cylinder block (20) with two new
lockwashers (22), screws (23), and screw (24).
2.
Install engine oil pan (WP 0312 00).
0313 00-4

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business