Quantcast CRANKSHAFT REAR SEAL MAINTENANCE - continued - TM-9-2320-386-24-1-20155

 

Click here to make tpub.com your Home Page

Page Title: CRANKSHAFT REAR SEAL MAINTENANCE - continued
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
CRANKSHAFT REAR SEAL MAINTENANCE
Up
/.5ton/TM-9-2320-386-24-1-2 Extended Service Program (ESP) for 2-1/2-Ton 6x6 M44A3 Series Trucks (Diesel) Manual
Next
CRANKSHAFT REAR SEAL MAINTENANCE - continued - TM-9-2320-386-24-1-20156
TM 9-2320-386-24-1-2
0305 00
CRANKSHAFT REAR SEAL MAINTENANCE (Contd)
REMOVAL
WARNING
Eye protection is required when performing drilling operations. Failure to do
so may result in injury to personnel.
1.
Drill three evenly spaced 0.161-in. (4.1-mm) diameter holes in rear seal (2).
2.
Alternating between drilled holes, use slide puller with adapter to evenly remove rear seal (2) from
cover (1). Discard rear seal (2).
NOTE
Wear sleeve will be present on crankshaft only if rear seal was previously
replaced.
3.
If present, remove wear sleeve (3) from crankshaft (4).
CLEANING AND INSPECTION
WARNING
Skysol-100 mixture is combustible. Use mechanical ventilation whenever
product is used in a confined space, is heated above ambient
temperatures, or is agitated. DO NOT use or store near heat, sparks,
flame, or other ignition sources. Keep container sealed when not in use.
Contact with Skysol-100 may cause skin irritation. Use chemical resistant
gloves. In case of skin contact, remove any contaminated clothing and
wash skin thoroughly with soap and water. Wash contaminated clothing
before reuse. Eye contact may cause irritation, tearing, or blurring of
vision. Use face shield or goggles when eye contact may occur. In case of
eye contact, flush eyes with large amounts of water for at least fifteen (15)
minutes or until irritation subsides. Inhalation may cause irritation to
upper respiratory passages. DO NOT have food or drink in the vicinity.
1.
Using Skysol-100, clean rear of crankshaft (4) and cover (1), and dry with lint-free cloth.
2.
Inspect cover (1) for cracks, breaks, and gouges. Replace cover (1) if cracked, broken, or gouged.
INSTALLATION
NOTE
Tighten locator screws only finger-tight so that when seal and seal sleeve
are installed they will self-align.
1.
Install locator on rear of crankshaft (4) with two locator screws.
CAUTION
Rear crankshaft seal must be installed with wear sleeve in place. Do not
remove wear sleeve from rear crankshaft seal. Failure to comply may result
in damage to equipment.
2.
Position new rear seal (2) on seal sleeve with beveled edge of wear sleeve (3) facing toward locator.
3.
Install rear seal (2) and seal sleeve as a unit over locator and tighten two locator screws.
4.
Position seal installer over locator, seal sleeve, and rear seal (2) and finger-tighten nut assembly.
5.
Tighten nut assembly to install rear seal (2) on crankshaft (4) and cover (1).
6.
Remove nut assembly, seal installer, and seal sleeve from locator.
0305 00-2

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business